|
Shad Poo
Mar 24, 2016 9:35:57 GMT -5
via mobile
Post by quackquackboom on Mar 24, 2016 9:35:57 GMT -5
I have a 35 SBT 2. The shad poo seems to build up in the center of the tank. I just try and "sweep" towards the filter intake when it does. I was curious if this is just part of the deal or if I was doing something wrong.
|
|
|
Post by mwardncsu on Mar 24, 2016 9:37:27 GMT -5
Yep - part of the deal with the circular current and heavier "poo" - some other tanks try to address this with a center-tank drain or even a center-tank filter stack... not really much you can do about it with a SBT other than sweep it to the filter or stir it up every so often.
|
|
johnr
New Member
Posts: 1,295
|
Post by johnr on Mar 24, 2016 9:54:32 GMT -5
I noticed this on my Xtreme tank as well, but just after the bait is initially loaded. After an hour or so of the bait stirring the water up and the boat sloshing it around, most of the mess gets filtered out.
I've thought of extending a piece of perforated half round pipe across the bottom center of the tank to pick up more of it, but haven't gotten around to it yet. I've also thought of upping my pump size to pull more water. Haven't done that either. I'm not sure either action is needed, the baits stay perfect as is.
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Mar 25, 2016 19:32:48 GMT -5
I get the same. During those moments of the day where I just stare at my bait, I will use a very fine mesh dip net to quickly get it out. It is definitely all an aesthetic thing....very similar to cleaning up your boat after your morning bait throwing session knowing that you plan to throw again in the afternoon. Now that I think about it, I am not sure why I spend so much time keeping my boat clean nor why I like to remove a few harmless pieces of shad crap from my bait tank. I just do!
|
|
Deleted
Deleted Member
Posts: 0
|
Shad Poo
Mar 27, 2016 10:48:25 GMT -5
via mobile
Post by Deleted on Mar 27, 2016 10:48:25 GMT -5
I noticed this on my Xtreme tank as well, but just after the bait is initially loaded. After an hour or so of the bait stirring the water up and the boat sloshing it around, most of the mess gets filtered out. I've thought of extending a piece of perforated half round pipe across the bottom center of the tank to pick up more of it, but haven't gotten around to it yet. I've also thought of upping my pump size to pull more water. Haven't done that either. I'm not sure either action is needed, the baits stay perfect as is. I would be wary of upping my pump size. I tried this and it created more of a mess by stripping the bait. A very slow circular flow seems best to me.
|
|
johnr
New Member
Posts: 1,295
|
Shad Poo
Mar 27, 2016 11:40:41 GMT -5
via mobile
Post by johnr on Mar 27, 2016 11:40:41 GMT -5
I noticed this on my Xtreme tank as well, but just after the bait is initially loaded. After an hour or so of the bait stirring the water up and the boat sloshing it around, most of the mess gets filtered out. I've thought of extending a piece of perforated half round pipe across the bottom center of the tank to pick up more of it, but haven't gotten around to it yet. I've also thought of upping my pump size to pull more water. Haven't done that either. I'm not sure either action is needed, the baits stay perfect as is. I would be wary of upping my pump size. I tried this and it created more of a mess by stripping the bait. A very slow circular flow seems best to me. That did happen to me with my creekbank, but the output flow seemed a lot stronger than in this tank. It could be my imagination, as I haven't tested it in any way. It works fine now, so i have no good reason to change it. Yet..
|
|